Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi there.
I recently migrated from SDK 13 to SDK 14.0.0 and followed the migration guide in detail. I've found that when I try to advertise, ble_advertising_start() will...
According to the nRF52810 datasheet,the reference circuitry with DC/DC regulator setup connet the pin DCC and the pin DEC4. Then how much is the voltage output of the pin...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I am trying BLE multirole application ble_app_multirole_lesc from the SDK 13.0.0.
I am using nRf52832 DK along with GCC toolchain.
For debugging I am using Segger...
In the mesh network, the sender uses trickle algorithm to control the repeat sending process, and at last the sender will send the message forever in a max interval at a handle...
Hi Nordic Team!
After developing our firmware on the nRF52 HDK, we designed our custom board, and we're starting to write our custom board configuration file.
The main...
Hi,
we've developed a custom board with nrf51 and use bonding and white listing.
Everything works fine when connecting and bonding iOS phones with this devices but with...
HEllo,
I was wondering whether or not is advisable to use the same handler to handle transmission/reception of data over SPI0 and SPI1 interfaces.
I have two sensors...
Hello
I am using a custom board, based on nRF52832 CIAAB0. I have also S132 installed, and I am using SDK 13.1.0. TWI pins are P0.16 - SCL & P0.18 - SDA. The code is based...
I am trying to advertise some data using the s130 softdevice to my MS49SF2 (nrf51822 based module ) and then flashed the hrs example code to it..
Still I couldn't find...
hi, Nordic
I'm using your nRF51-DK(PCA10028) board, on android, i disconnect connection by call BluetoothGatt.disconnect ( developer.android.com/.../BluetoothGatt.html ,...
Hallo i am beginner developer, i plan to send sensor data to smartphone, i am still confused whether to use ble_app_uart or advertising mode, for example my case saw TrackR...
Currently I am using the spis driver to send data through the SPI peripheral. On the event handler I want to capture the time in which the chip is selected, which in the case...
I just opened my nRF52 DK and tried to flash the board. I got the error
ERROR: There is no debugger connected to the PC
Most concerning is that the LD5 light does not...
I have two nrf51-DK's (say A and B).
A , nrfStudio doesn't detects it.
(Windows doesn't even shows USB port connection in device manager, so cannot try nrfjprog -...
