Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi Nordic Tech Team,
I am implementing BLE-based FOTA for the application core on an nRF5340 using MCUboot . The update works successfully when using the nRF Connect mobile...
Greetings to everyone.
My name is Toni, I am a beginner. I have a device, which my former colleague left to me, and I can not identify the HWID. How HWID should look like...
Hello,
we are trying to perform FOTA updates with default SLM application based on SDK 2.9.0, but the application always aborts unsuccessfully.
Via AT interface the application...
Hello Everyone,
Happy New Year !
We would like to evaluate nRF54L15 system off/deep sleep mode current consumption. So we have tried the existing example ( https://github...
I just received the nRF21540-DK and am trying to see the range enhancements.
I simply created a new application by copying the "Bluetooth Peripheral" sample in Visual Studio...
Hi,
In the attached hello world example that I modified for the nRF5340DK board, the nRF UARTE serial driver doesn't exit low power mode when I type any characters on my...
Hi everyone,
I've been developing an application using the nRF7002DK, where the nRF5340 SoC communicates with the nRF7002 SoC to connect to a Wi-Fi network, retrieve a JSON...
Hi, I'm quite new with the nrf ecosystem. I'm trying to setup a nrf52833 development board to use an AHT20 as a humidity and temperature sensor. I tried coding my one i2c...
Hello,
I’m trying to obtain millisecond precision on nRF Connect using the MCU’s internal RTC.
My code:
After 131000 ms, a got:
Could someone help me find...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...
