I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
Hello I am looking for the IBIS model for nRF52840 for signal integrity simulations. I saw similar requests older than 2yr and I am wondering if now the model is available...
Hi, I am having problem making DFU work on nrf52832 using nrf connect sdk 2.6.0. Below is my mcuboot.conf under child_image and prj.conf. Please guide me where I am wrong...
Hi all,
I am running the lsm6dso zephyr sample on my nrf52833 dev kit. I am unable to set the sampling frequency. I get this error after flashing:
This is my overlay...
I refer to and the answer answer given by AI referring me to you.
I need the lithium battery only to about 8-bit accuracy to reduce the leakage current. Please provide...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
Hi Everyone,
I am having problems writing to an array in NRF52832 without causing the program crashing at run time.
I declare the array to be 512 uint8_t long
then...
hi, I'm a fresher of this kind of development. My boss give me a board and let me run the Zephyr OS on it. But I am not sure whether I lack some things and how to assembly...
hello I am just needing some clarification on meshing. I am using the long range nfr52 chip. I have a transmitter with a tilt switch that connects to my receiver when connected...
Dear Support team,
could you please advice how can I change the endpoint where Thingy91 sends the measurement data stream from the sensors?
By the default it it is the...
HI, I'm Rafael Fajardo a student at Las Palmas de Gran Canaria University . I am using the nRF51 Dongle and following the Sniffer User Guide, but when I got to the final step...
Hello,
Zephyr has their own Bluetooth stack. Has anyone done an objective comparison of the Zephyr stack to the NRF52 soft device stack? I am very familiar with the soft...
Hi,
I'm currently making energy measurments with an nrf9160 DK. The software project is based on the udp_with_psm sample. I would like to run the test on different tx-power...
When debugging with Keil, the software may suddenly start from the beginning. The reset process may be running somewhere, but it cannot be detected. Is there information that...
Hi everyone,
I am a beginner developer, I'd like to know what's the difference between different softdevices.
In particular I am using SDK 10.0.0 with softdevice 110...
Dear Sir,
I am using Example beaconing_nrf52840_xxAA_s140_6_1_0 in nrf5 SDK for Mesh_v3.0.0 get stopped after running for sort period. I have tried to debug but could not...
Hi,
sd_ble_gatts_hvx returns 13313 in some rare cases involving the phone is far from the nrf52840.
My questions:
1. What this return code means?
2. What is the recommended...
I am trying to connect the device to android phone both on nRF connect as well as normal pairing. Both seems to not work.
I get this log from the device:
on_ble_evt: BLE_GAP_EVT_DISCONNECTED...
On \nRF5_SDK_15.3.0_59ac345\examples\peripheral\radio_test, there is the pca10040 project.
I can't find the pca10040e project.
So how can i to port the project to NRF52810...
