I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Please, share the firmware of the board nRF9160-DK PCA10090 version 0.8.5 , which is flashed into a new board. The firmware that I received using the instruction ( https:...
Hello,
I am using NRF52832(WLCSP package) and nRF5_SDK_15.2.0 for the product.
I also use IAR Embedded workbench 8.32.1 as IDE.
Few hundreds devices are assembled...
Hi,
I'm trying to figure out how to ping a specific IP Address from the nRF9160 via AT Commands. I can't seem to figure out how to do a simple ping to an internet server...
Hello! Board nRF9160-DK. Compiled and uploaded the project asset_trecker (merged.hex). The LTE Link monitor shows a cyclic reboot. LEDs do not blink. where is my mistake
Sorry,I want to know whate is the different between BLE_UUID_TYPE_BLE and BLE_UUID_TYPE_VENDOR_BEGIN, the Device name will become N/A when I use BLE_UUID_TYPE_VENDOR_BEGI...
Hi,
I'm studying the example about the nrf_crypto for implementing asymmetric encrypt and decrypt function.
The suggestion on the Dev_Zone is to use the share key to symmetric...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
My app runs the following code, that is supposed to init the SoftDevice:
nrf_clock_lf_cfg_t clock_lf_cfg = { .source = NRF_CLOCK_LF_SRC_XTAL, .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Dear Nordic,
We have developed a product utilized the NFC readable/writable feature of NRF52832. We have tested it against some of the HTC, Sony, Samsung, and Google phones...
Hi,
I will add feature "installation codes".
I guess that security API do work.
At coordinator side, zb_secur_ic_add, zb_set_installcode_policy functions
At end device...
I am trying to implement nRF52 Light Switch Proxy Server in nRF52832 boards. Everything works fine on behalf of board and it prints the Device UUID as well. Although I can...
i'm using nRF mesh sdk v2.1.1 with 2 boards and 1 provisioner board. I have un-provisioned 1 board with the help of config_client_node_reset(). I want to know the procedure...
Hi,
In your Light switch example, there is a GPIOTE_IRQHandler() in simple_hal.c. Since I added the nrfx_gpiote module to the project, this is conflicting with the nrfx_gpiote_irq_handler...
Dear：
I used the nrf9160DK version to 0.8.2, updated the latest firmware mfwnrf9160100, using the NBIOT SIM card, and using the SDK version as nRF Connect SDK V1.0.0. After...
