Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
I would like to create a repo to house all our vendor-specific board support, applications, etc. outside the Nordic nrfConnect repositories as per the Zephyr workflow. However...
Hi, I am an internship student and so new at programming. I have a nRF51822 DK that includes;
2 x nRF51822 module
2 x BLE master dongle
J-Link Cortex emulator (Debugger...
Hello everyone,
We have an IoT device with the nRF52832 module installed. We are in pre-production and in the process of certification. Our laboratory (EMITECH) asks us...
Hello team, i use board nrf52832 and SDK15.3. in example ble_app_uart_c. BLE_NUS_C_EVT_DISCOVERY_COMPLETE event occurs only once, after losing the connection and reconnecting...
Is there an example for setting up a Segger Embedded Studio project for using an nRF52840 with Zephyr. The instructions on the Zephry site for adding Zephyr files to a project...
Hello,
We are currently designing a device that will use the GPS on the nRF9160, our implimentation will involve using sensors to trigger GPS measurements for the duration...
I am using an nRF52832 and the Nordic UART Service (NUS). I am using the example NUS code and the UART side is plugged into another microcontroller's UART. By default that...
I need to find rssi value of my mobile (using nrf blink app) using nrf52840 Dk.. So i generally don't have idea what changes to be made for ble_peripheral->ble_app_blinky...
Looking at different solutions to an asset tracking system I'll be working on as my senior project later this year (getting a head start so time isn't as much of an issue...
Hi,
I'm writing a driver for a Ublox cellular module, which will be communicating with the nRF5240 using UART. After going back and forth, I decided to go with the app_uart...
Hello, I am an intern at a startup company and ive been tasked with finding some information about the chip set we are using, specifically the bluetooth aspects. We are using...
Hello,
I just installed SEGGER Embedded Studio to build the light switch example for Bluetooth mesh.
I managed to successfully follow the quick start guide using 3 development...
Hello!
I managed to flash my Raytac dongle with debugging going using the SWD on a nrf52 DK. I am mainly working with SEGGER Embedded Studio and nRF Connect on Mac. However...
i m getting constant RSSI values 32 even if i move far or near
this is the same example code in ble_peripherals
I HAVE UPDATED MY CODE (i have printed the RSSI values...
I have an android smartphone of bluetooth version 4 and i am developing one application where i am using nRF52 (bluetooth version 5). Is it possible to write data from the...
