Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Is there a way to modify the code in the ios nrf beacon app to identify nordic beacons?
I am aware that the manufacturing id must be set to 0x004C in order to be identified...
Hello,
Is it possible to create a GATT service with a 128 bit UUID, where each characteristic has a unique 128 bit UUID of it's own?
Looking at the examples, it seems...
Hello guys,
During implementation of a test set for CryptoCell AES CCM* functionality i'm facing some issue with the CryptoCell.
Encryption works fine without any issue...
Hi,
my application application consist of NUS service, one i2c, one spi and one adc. it consumes around 10-11 mA while its running. its was observed that while only running...
I am using APP_TIMER to turn ON and OFF pwm. PWM is used to drive a buzzer. PWM is turned ON and OFF in the APP_TIMER timeout handler.
It is observed that after starting...
I have now spent a significant amount of hours debugging strange problems with my advertising. It turned out that it is very important how you set up the init structure for...
hello guys
i am trying to glow LED while my device gets charging. i have nrf52832 custom board and P0.17 connected to USB supply using voltage divider. when i plug in usb...
Hi all ,i wanted to know how to start programming with nRF 51822. i have tried many times to load or download program but i failed .actually im new in nordic programming even...
Nordic offers many features in their libraries that rely on callbacks, but the use of void *context pointers to allow proper object oriented programming is sparse. For example...
Hi,
I'm currently working on an application that collects audio data and sends it to a central device via BLE. Since audio compression has great potential to reduce power...
Hello Sir,
We developed one application in that we use WiFi and interface this to nRf52832 chip using UART. The WiFi Ch_PD(Chip enable Power down = GND for low power consumption...
Hello everyone,
I would like to know how the (G)FSK modulation on nRF52832 is realized. Is my assumption correct, that a Fractional-N PLL in combination with Delta-sigma...
I have the precompiled code running on two seperate nRF52832DK PCA10040 1.2.1 boards. The example appears to do exactly what it said it would do. However I cannot detect any...
I am getting the following errors.
Building ‘1’ from solution ‘1’ in configuration ‘Debug’ Generating linker script ‘1.ld’ Linking 1.elf Output/1 Debug/Obj/ses_nRF_Startup...
Hi,
On STM32 and some other platforms I'm able to get an address that I can write to in order to set the value of a single pin. While (like on nRF) there is one output register...
