Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
I call the following function to delete old FDS records before I write a new record. It works well if I have only one old record. But when there are multiple records, it stops...
When I use nrf_drv_gpiote driver by sdk8.1.0. with softDevice 8.
I got HardFault_Handler when run in
handler(pin,polarity); in the GPIOTE_IRQHandler
How to deal...
Hello,
I use stack S110 V7.1.0 on nRF51822 (the device is a remote with 4 buttons).
Currently the remote send advertising frame with the pressed button into the data,...
I am writing code for nrf51822 with softdevice and an accelerometer is connected to the nrf chip. The accelerometer provides interrupt to nrf chip over GPIOTE whenever there...
Hi Nordic,
I am trying to extend DFU feature to my beacon application. Please help me with how to go about it. I went through the given tutorials on DFU/OTA, but I haven...
Hello sir,
I have develop my BLE_UART code is working fine with nRF52832 DK board but when i flash into spark fun nRF52 is not working. But i able to flash into Spark fun...
nrf51-Dongle keeps on connecting and disconnecting (to the PC) when inserted into the usb port of the PC.
Also it is getting heated up upon keeping it in the usb port for...
i am working on aes_ccm with '802_15_4_lib_keil.lib' , and i have build the target,but the result is not right. since there is no example with this lib,
now i have a big...
Hi,
I have a problem with (128 bit) custom service discovery... I have following setup; nrf51 with s130 in central role and Thingy with default FW.
In function on_primary_srv_discovery_rsp...
Hello,
I've moved my project to SDK 14 and SD 5 and that updates were working correctly in a loop (rebuilding app FW, merging BL+SD+APP, doing DFU). Today I've noticed...
I'm using a NRF52DK with Zephyr controller build attached to Bluez 5.45 to scan, connect and discover characteristics on up to 16 devices in parallel. While testing, everything...
Hi everyone,
I am using board PCA10040 v1.1.0, softdevice 13.0.0, Eclipse Oxygen. I am trying to scan my phone and communicate with it but the scaned UUID is increasing...
Suppose I configure RTC0 and RTC1 to have the same LFXO clock source (with a 30uSec tick) and start them in quick succession. Will their counters read the same value?
I...
I just started trying to get an IOT IPv6 application up and running. On the nrf51882 end, I have flashed the IPv6 COAP server. The LED on the device is happily flashing away...
