Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
Hi !
When operating the Thingy52 with it's factory firmware:
Is the Thingy 52 choose automaticly which BT protocol to use (BLE 4.1 or Bluetooth 5).
I mean:
if i connect...
Can someone revise
www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
to include an image from an Apple Mac .(I can provide one)
As well as modifying...
Hello,
I am trying the example code, heart rate BLE peripheral application, on the nRF52 DK. However, I cannot see the screen fill with data in the heart rate monitor,...
hello,
i am working with a long range ble long range transmitter and receiver which will communicate over long range to send a ble nus string in nrf52840, so i set tx power...
I am working with SPI and SPIS examples ( sdk version 13). SPI of nrf52 is full duplex. In the example, I can send data from Master board to Slave board then Master board...
Hello!
I use 2 board nrf52840! I want to transfer large data ( 1~2MBytes) from board1 to board2 with wire to connect. Can have solution for me? (SPI I2C or uart).
According to the description of S132_SDS_v5.0 on page 82, when the establishment of connection, in accordance with the BLE protocol, softdevice will be interrupted frequent...
I am using nRF52840 and the power profiler. I am trying to measure the current to evaluate the scheduling of BLE. Now I am using the ble_uart_c example and I changed the scan_interval...
I'm trying to set up SPI example from SDK12.3, but I get error at line 53 of main.c
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
It's saying...
Dear friends,
i am using Power Profiler Kit with a nRF52832 DK(PCA10036). However, i just find three versions of SDK on www.nordicsemi.com/.../nRF52-DK . My problem is that...
Hi nordic,
nRF5_SDK_14.0.0_3bcc1f7\Raga\examples\ble_peripheral\ble_app_ancs_c FDS\pca10040\s132\arm5_no_packs
I had a problem when I was using FDS，When I use the GC...
Dear friends,
I want to use Power Profiler Kit to monitor the current waves of nRF5x DK, and i followed the following configurations:
The PPK board (PCA63511) is connected...
