nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
When I connect the nordic ID stix to my android tablet using the micro-USB to USB cable, the nordic ID stix doesn't appear green light on it. Is it need to install any driver...
I would like to dynamically change bluetooth LE advertising interval. I am using nRF51 and nRF52, with SDK's 8 and 12. Is that possible and how to do it?
Our application...
Good day everyone,
I would like to utilise the nRF52832 BLE chip in an application that requires radio communication between a master and slave. The slave needs to be powered...
Hi everyone,
I am using LPCOMP in rFF58122.
When coosing the reference voltage, I have to fill the structure nrf_drv_lpcomp_config_t with the hal nrf_lpcomp_config_t that...
Hello, I try to add TWI function in my project (uVision5) so I add this modules with 'Manage Run-time Environement':
nrf_drv_twi
nrf_twi
app_twi
and I get...
hi
I have a problem in integrating a 1.8V GSM modem with nRF52832 through UART. nRF52832 supplied with 3.3V and there is a voltage divider that covert 3.3V to 1.8V in the...
hello....
Nrf 52832 does not work.
With a newly developed board,
Programming with nrfgo studio and J-link is not possible.
It feels like it does not have a good reset...
I'm looking for an example code of central role which can run on nRF52 DK.
I want to check if it is possible for nRF52 DK to send a LL_CONNECTION_UPDATE_REQ PDU to slave...
In general, I'm working on my own dfu-bootloader project which was developped on the "Engineering A" chip-revision of the nRF52832. We finally have new hardware with the chip...
Hi all,
I have use nRF5_SDK_11.0.0_89a8197 and S130 before and use nRF Toolbox to do switch it to bootloader and do OTA, just use one APP. However, now I'm using nRF5_SDK_12...
Hi,
I look at this demo,found that the ESB is PRX in most time, it may lead to a high power consumption.I want to achieve auto ack, piggybacking data in ACk from PRX.So the...
Hi all, I'm working on experimental_ble_app_buttonless_dfu project in sdk13-alpha using pca10040 board. I just compiled experimental_ble_app_buttonless_dfu successfully for...
Hello all,
I am implementing an energy efficient system, in which I am advertising in BLE_GAP_ADV_TYPE_ADV_SCAN_IND mode, I am using scan_req_report as an acknowledgement...
I'm trying to following example of nRF51_SDK_v12 OTA-DFU Example , but there are no support with BLE400 at all. (BLE 400 has nrf51822 QFACA1 1536EK Chip on it)
I think...
Hi Nordic Team,
Please I would like to ask how can I globally identify my device (nRF51822) based on its address?
Assuming that:
The address type of nRF51 is...
