Hi,the Nordic team
I am developing Matter over Thread on nrf54l15, this device is a SED battery powered device, how can I measure the remaining battery power?
Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
Following is a simple application that I have created. It has no softdevice and the configuration is very similar to blinky freeRTOS example.
Source code:
main.c
...
Hello ,
I'm working on custom board, I'm trying to disconnect from the Central (Andriod app) when the battery is below certain level and stop re-advertising.
Below is...
In s130 Soft device v2.0 document, it says it can have role with up to 8 Role concurrent with Central, Pheripheral, Advertiser, Observer.
I'm not sure i've understand all...
Hello. I'm using nRF52832, PCA10040, SDK13, S132 and "ble_app_uart" as reference.
When I connected board through by bluetooth, I couldn't see notification message which...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
Hi Nordic team,
I print logs at each function in ble_bas.c. I used the App of nRF connect to test BAS. I can see on_connect, on_disconnect and on_write at enabling/disabling...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...