nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
hello
i am using redbear lab's ble nano with nrf nrf51822 chipset in it. now i need to permanently store some data like sensor values and mac address of central devices...
I'm not able to find an older legacy version of Softdevice S110, specifically 7.2.0.
In the SDK Version 7.2.0 obtained from:
developer.nordicsemi.com/.../
there is...
Hello
I want to establish the connection between nrf51822(base station) and:
the second nrf51822(transceiver)
android smartphone(transceiver)
It has to be possible...
Could someone offer some guidance in how it is possible to keep the radio within IDLE mode between transmissions when operating in ESB mode? I have a sequence of transmissions...
Hi
I'm doing some S/W based on nRF51822_xxAC. I want to split RAM into 2 regions, as following:
+-------------+ 0x20008000
|__ __ _ __ |
|APP ZONE2 |
+-------...
hello, I'm trying to read the status register but all I am receiving is 1111 1111, I tried to change the code to read RX_ADDR_P0, but I also receive 1111 1111. can you tell...
It suggests that it holds the permission regarding whether a chara. can be read, but isn't that kinda redundant since there are tons of other similar properties out there...
Hello
Can i program an nRF52 chip using nRF51 DK. I plan to take advantage of the features of nRF52 including higher memory, storage and the NFC
Thanks
Hi,
My company has been running into an issue with the NRF51822 where the MCU appears to enter debug mode unexpectedly and I wanted to see if any others had experienced...
I successfully used my nrf52DK with latest production SD 132 and latest SDK (12.2.0), everything is on latest Keil v5. Then I needed to program another board (nRF51 Dongle...
Hi Nordic Tech support team，
I have some problems with nrf51822 OTA.
My Bootloader is single bank Bootloader。When I update nrf51822 firmware by OTA with android apk, I found...
Hi i'm very frustated with myself not the modules , i could make a pair of them to work perfectly in a pic 16F886 , now due to other project i have to use a dspic33fj64mc202...
We made a version of bootloader_secure for our own purposes. The problem is now that application must be uploaded twice into the device (nRF52) before it really gets updated...
Hi,
I am working on bootloader_secure example on SDK_12.1.0 and set APP_ADV_TIMEOUT_IN_SECONDS to 180 to stop the advertising after 3 mins.
All looks fine and device...
