I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
This should not be a sudden my PCA10040.
Jlink are probably going to have failed.
It does not appear in the USB Jlink to appear as Atmel.
Is there a way to recover...
I am doing a project about nrf51822 smart beacon kit and a person has give me this link: infocenter.nordicsemi.com/index.jsp
to download the firmware and hardware files...
Hello,
I develop a BLE central device based on nRF52 (with the newest connectivity firmware and SoftDevice with API v3) and the pc-ble-driver in version 2.0.
Since my...
Hello Everyone,
I am working on nRF51 I need to save data with timestamp (current date and time).
Is there any example code is available so I can set current time and...
Hello,
Recently read about FIDO’s U2F authentication protocol for NFC and Bluetooth smart.
https://fidoalliance.org/fido-alliance-equips-u2f-for-mobile-and-wireless-applications...
hello everyone,
I am doing a project about Ibeacons. I need to make a selfmade bluetooth smart beacon (excuse me for bad English). I found a schematic circuit design of...
Hi all,
I am trying to get an Android Nexus 5X app to work with an NRF chip, and facing some problems, specifically with writing to a characteristic. Really hope to get...
Hi,
I discovered unusual behaviour in a SPI read transfer.
My transfer consists of writing one byte (peripheral register address) and receiving one byte (contents of...
SoftDevice Version s132 SDK Version
12.2 Kit NRF52832 PC10040 DK
I am trying to run the ble_app_beacon example after importing the project into Segger Embedded Studio...
Hi,
My application always stops at the end of ble_stack_init() exactly at:
return sd_nvic_EnableIRQ(SWI2_IRQn);
of the function softdevice_handler_init.
My board...
I am working on a project using the nRFDK51 as BLE scanner with s130 and BLE peripheral an nrf51822 custom PCB design. The BLE peripheral is the device we are developing for...
How many nRF52840 chips can be used simultaneously? Can all data and advertisement channels be used at maximum capacity (2Mbps/each) to result in an overall throughput of...
Hi,
I am running an nrf52 (board PTR5628, no external 32kHz crystal), having some leds blinking at startup just prior to start advertising. 75% of the time when I power it...
Hello all,
I have created a BLE application on nRF52 PCA10040 devboard with S132 SD, in which I would like to use a PWM with the PWM_Driver .
My pwm source code as below...
