I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
I'm trying to get a simple "Hello world" program to run on the Nordic ID Medea.
As soon as I start debugging I get the error "The bootstrap could not be loaded".
Any idea...
I follow this:
developer.nordicsemi.com/.../a00092.html
Creating an image file
The format of the firmware image that you use to update the device firmware depends on...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
At the moment I am working on a project that uses the nRF52328 acting as both a peripheral and central to connect 3 separate devices intermittently. I am storing their bonding...
Hello,
I use SDK example nfc_text_record for pca10040 DK.
With aim to check memory area of the emulated tag I've modified example with next:
/* Set up NFC */
err_code...
Hi,
i am working on PWM to operate vibration motor with different frequency levels. so that i integrated PWM Library example to my ble_app_uart example. in the PWM example...
Faced with problem in subject during porting Serialisation to STM32F4 chip.
Serialisation library extensively uses function call triggered by NVIC.
How to substitute this...
I'm using ANSC example, pca10028, iphon5s and iphon4s.
I confirmed #define DEVICE_MANAGER_MAX_BONDS 7.
But pca10028 cannot pair with iphone5s after paired with iphone4s...
Hi,
I'm using nrfutil to update my nRF52832.
I change target from nRF51822 to nRF52832 and I want be able to bootload my target through own master.
In past, I used...
I have followed instructions at the link below to setup a Raspberry Pi 3 as a 6lowPAN router, and am trying to run the dns example from nRF5 IoT SDK 0.9.x on an nRF52-DK:...
Hi,
I'm using pca10040 and prebuild hex with s132 from sdk 12. Now I'm wondering how can I get number of sent data? If I set it as transmitter - send via uart 0x8094 i...