Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi,
Currently i am using ble app uart as a reference example and nus service with soft device S130 for our project. I want to use multi role example (central and peripheral...
Hi !
I'm trying to run the BLE bootloader example ( here ). I succesfully programmed the SoftDevice and the DFU bootloader :
The device start in bootloader mode ...
Hi, few days ago when I attach the nRf51-DK and try to read the content, the nrfgo software freezes or crashes.
If it freezes i can see clearly the content stack of the...
Does anyone know what's the maximum acceptable input timeout_ticks of function
uint32_t app_timer_start(app_timer_id_t timer_id, uint32_t timeout_ticks, void * p_context...
Hello,
I really need the ability to switch between different advertising messages. Could you please (please!) add a callback after an advertising message has been sent...
We are using the NRF board to act as node.
Samsung Galaxy S6 device is being used as the Router. We are trying to ping the node using ping6 command.
The issue is that the...
I have a working peripheral NUS application to pair/bond by entering passkey in the nrf master toolbox android application.
Now i want to replace the mobile witha nrf 51822...
nrf51822bluetooth low energycode 10
twiddle gravatar image
twiddle
1
asked May 9 '16
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
Dear Sir:
I have a (BLE + 2.4GHz)Mouse project, But now I had some problmes. Please help deal,
Thank you so much Sir.
a). My program modification base on "nrfready_desktop_2_v3...
Hello all,
Just to note any versions that need saying, I am using
SD 110, V8
The 10.0 SDK, freshly unzipped
The dual bank BLE bootloader, unmodified
Arm...
I was looking at this PA/LNA example: here . I noticed something I'm not sure about, so I was hoping someone could shed some light on this.
In the diagram shown in the...
