Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
HI,
We are producing products using the nRF52832. During production, a defect occurred where the lpcomp detection voltage was operating at a voltage lower than the design...
HI
I'm using nRF54L15-PDK 0.8.1. When debugging with VS Code, the debug session failed for some unknown reason. Afterwards, the PDK's nPM1300 output, which was originally...
HI
We are mass producing products using nRF52832.
However, during production, a PCB was found to not detect low battery voltage for about 5%, so we are inquiring about...
As the title suggests, we are having issues with BT notifications being throttled.
The function which does the notifications is below:
We loop over sectors of flash memory...
I am trying to replace such a platform and was hoping to use nRF9151 as a starting point.
Is such a platform possible at all with Nordic/Zephyr ?
I have an old 9160 dev...
I am trying to use Edge Impulse ML models on my custom board. I have built my model on EI and downloaded it locally. I followed the sample wrapper code to use my own model...
Hi, I am devolping a sensor system where I am in need of a Tri state GPIO solution
Currently using the NRF54l15DK with all the latest software versions (3.11, etc.), developing...
I am trying trilateration for indoor positioning system with nrf54l15 , using 3 initiators and a reflector I was not able to switch between initiators and also one of the...
Product is a zigbee router.
Use nrf connect sdk 2.4, update it is not an option.
The zigbee join work fine most of zb3.0 coordinator, BUT with an old coordinator it failed...
Hi all,
I'm using aws iot lib and last will topic feature, everuthing works but I have a question, in prj.conf I set my topic with
Is it possible to build this last...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . In our setup, sometimes the PMIC powers up and works correctly, but other times it does not...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
