Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am experiencing an issue with my nRF52840 DK board. When I initially connect the board to my PC via USB, the debugger LED (LED5) blinks briefly but then turns off. Additionally...
Hi,
I'm looking for some guidance.
I'm using a HolyIoT nRF54L15 dev kit to evaluate their nRF54L15 module.
I am currently looking power consumption.
I have tried the...
I'm wanting to repetitively read the SPI buffer as a master to check a status bit. I figure there's no sense in using the DMA when I can read the SPI RXD buffer directly....
Hi
I am trying to use the two GPIO pins. One GPIO pin is configured as a input and connected externally to a button.
The second is configured as an output pin. I want...
I am trying to complete the course "nRF Connect SDK Fundamentals" using a nRF52840 DK board (version 3.0.0) connected to a Mac Mini (Intel processor) running macOS version...
Hello,
I'm experiencing high current consumption with Zephyr OS. I'm using SDK 3.1.0 and the device still draws about 900 µA, and I don't know why. Although I have a custom...
Hi all, I am going through the beginner course and am using the MPU-6050 over I2C. I am able to communicate with the board where I get the WHO_AM_I. I can also read from the...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
Hello,
I want to have 2 applications running on nrf5340 CPUAPP (nothing on CPUNET) with app1 in flash and app2 (in RAM) getting launched by app1 once placed in RAM as a...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
