I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Can somebody please confirm whether the following piece of code will use a 32-byte encryption key stored in KMU slot #4? I've successfully tested encryption/decryption using...
Hello,
There are many questions out there on correctly determining the SAADC pin input voltage limits. The equations given in the product spec is very straight forward:...
Hi, I am working on a project that utilizes the nRF52832. How to properly enable Access Port protection in the code, if I want to have a single firmware for all three revisions...
Hi,
I was using the Direct Test mode app from the nRF desktop to try to run a DTM Tx Test on nRF54L15-DK. The app could find the device (but there're two serial ports xxx51...
Hello,
I am currently working on a project using the nRF54 Series and I am evaluating the capabilities of the CRACEN versus the nrf_oberon software library.
I would like...
Hi,
I am wondering why can't CODED PHY and BLE Audio be modded into the nRF52832. Are there any hardware requirements for both to be supported ? If so, is there any info...
I observed that I can't flash my board in VS Code when a USB-serial adapter is connected to my computer. When the adapter is unplugged everything works.
The interesing...
nRF54L15 + NCS 3.02 + Toolchain 3.02
So I have followed Dev Acadamy exercises for Serial Recovery and BLE FOTA. In my project I now have MCUBOOT for Serial Recovery but...
Hi, we are writing the register TASKENTERSHIPMODE to enter ship mode, and everything works ok. But as the ref manual says, when VBUS is present this task is ignored.
Is...
Hi,
We are working on the nrf5340 and our current device firmware uses the NCS 3.0.2 (i.e. nRF Connect SDK 3.0.2). We wanted to try an upgrade to NCS 3.2.1 and followed...
Hi, so my intention was to test the free subscription of Memfault with the thingy91 I created my account in nRF Cloud but the button to access Memfault is not there, I had...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi,
We’re looking for the SBOM and the official CPE identifier for the Nordic nRF5 SDK, specifically version 15.3.
We would need:
The SBOM for nRF5 SDK v15.3
The...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
