Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Dear All,
I need your help because I created a PCB with the nrf52840 and a flash connected exactly as the one on the dev-board.
The only difference is that the one on...
I am using nrf52840 . I am sending data 2 bytes as FF .I put the data in 2d array like this. char dataSend[1][5]={"FF"}; This char dataSend has 1 row and 5 length .This should...
I need transfer data to/from NRF52840.
I see I can do it by using function nrfx_usbd_ep_transfer - but don't see any examples.
I want to make bulk endpoint and be capable...
Hi,
I am running ble_app_blinky example on nRF5280 custom board, it is giving me Error 133 (0x85): GATT ERROR . Since I have nrf52DK, I tried same example with SD 132 on...
Hello,
i am using the NRF52832 and the NRF52840 with different softdevices. Now I want to update the softdevices over the air and I need the SD Version strings of all the...
A bit more detailed: A bug has been detected on the device under development. It is connected with the fact that if you try to disconnect a connected device on an iMAC Catalina...
Hi
I am trying to install the SES toolchain on my PC (Win 8.1) following exactly the nRF Connect v3.2.0 Getting Started Assistant. When trying to "Open nRF Connect Project...
I am using a nRF52 DK to program an externally powered board with a NRF52811.
I am able to flash a blinky program onto the custom board successfully using the output .hex...
Just as the title says, I'm trying to measure an input pulse width using PPI and GPIOTE. I am currently measuring the pulse width using timer interrupts, but I would like...
Good day!
generic_ponoff_setup_server_init causes Mesh assert error.
If I delete reallocation of dtt and onoff servers' subscription lists everything goes fine.
What...
Hi!
I have been using LoRa for communication for my product. I'm looking into using BLE mesh.
I have a couple of hundred sensors, all 1-2m apart from each other. Here...
In this scheme we use 2 inductor in a serial connection. 15 nH + 10 uH. Total inductor = 10.015 uH. ??? Is really need to add this 15 nH inductor? For why? If we just short...
When calling access_model_subscription_list_dealloc() from models_init_cb() an assert is triggered in sublist_invalidate() due to mesh_config_entry_delete() returning NRF_ERROR_INVALID_STATE...
I have 3 Nordic nrf52840 USB dongles , several Particle Mesh Argons and have ordered an Arduino Nano 33 BLE Sense and have found the Adafruit Feather nRF52840 Express . All...
Hi,
Greetings!
I am facing a issue while updating firmware
My Setup:
SDK 16.0.0
SDK for Mesh 4.0.0
nRF52832
DFU: secure_bootloader_ble_s132_pca10040
Application...
