Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
According to this thread, GPS sensitivity of Thingy:91 does not seem to be good while I haven't tested this yet.
https://devzone.nordicsemi.com/f/nordic-q-a/51424/thingy91...
Hello.
I have found this document and have a question.
In according with document below: service " Generic Access" (UUID1800) has a few characteristics: " Device Name...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
Hello,
We start using of our BLE devices with more or less permanent connection with our central BLE device, it was needed for Alisa connection.
BLE peripherals are old...
Hi,
I am a beginner in nRF52840. I want to add a channel hopping feature in the 802.15.4 example .
As per my understanding of source code, we can set the channel number...
I am looking for a way only a known/trusted device can connect and write/read information from my device. Filtering by address(white-listing) is not feasible. So what is a...
Device:
Peripheral only
Peer Manager and Bonding working
S140 radio
nRF5 SDK 15.2.0
Rigado BMD-340 module
Central == iOS devices
Our nRF5 module is controlled...
Hi, I'm on last step of developing, but I have this critical trouble. For the project, I started from ble_app_buttonless_dfu sample of SDK15.3. I added some peripheral (one...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
