The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi
i am using nrf52 dk wiht IAR embedded workbench IDE ARM 8.20.1
i want to disable the attach to running target from my device HZX-52832-S01A.
which bit i have to turn...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit (PPK).
I want to change the voltage supplied to nrf 52 arbitrarily.
I used the following case...
Hi everyone!
How to change erase range in DFU during application upgrade ? I have some data saved in flash (by psotage on 0x0007e000) and I don't want to lose them after...
Hi,
What is the advantage of using a Bluetooth SIG defined profile over a vendor specific profile? For example, if we want to transfer battery levels, can we define our...
Hi again,
Hope everyone had a great Christmas.. I did, but Santa also gave me a litte issue with my nRF52-DK..
I using a modified UART example, I have a 5min repeating...
Hello,
Basically my arrangement of NRF network is one receiver and multiple transmitter consider example 1:40 and they all configured with same address,bitrate, checksum...
Hello,
Is there a demo project that contains RTC function with softdevice.
I called the lfclk_config() and rtc_config() function before softdevice initial in main(), but...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
hi,
10040 nrf52dk
softdevice 132 v2.
keil ide
I am trying to read magnetometer values so that i can calibrate it using this method . For this to happen, i need magnetometer...
Hi guys,
I am using FDS module in nrf51822, sdk 11 to store and read data from flash. I have a problem about reading the data. In the documents, the function:
fds_record_open...
The problem
I am trying to build the examples contained in Bluetooth Mesh stack, but I get the following error when running cmake :
...
-- Found assembler: /usr/local...
