Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Is exist any way to detect IDLE RX line on UART?
I try to use RXTO but this is seted each time when 1 byte comes.
everytime, it changed size of data which will be readed...
Dear Team, I'm preparing an application for nRF52840 that will require to send and receive data collected from two different sources, I2S and UART, two UART or SPI and UART...
Hi Nordic,
Please provide the way to debug not able to write 14 Bytes data into Queued Writes module, my application not get any nrf_ble_qwr_on_ble_evt.
[Project Informaiton...
I am a little bit confused on the steps I need to follow to program the settings and the bootloader files. According to Secure DFU over Serial example instructions ( https...
Hello,
I am trying to download the program to my target using J-LInk. Unfortunately, I get this message (see bellow) and I don't know how to proceed.
Any help is appreciated...
Hi,
I am working on a project that utilizes mesh technology. I'm currently using nrf52832 with NRF Mesh 4.0
There are multiple devices that can act as a server and a...
Hi Folks,
Need some advice. We are sourcing voltage to a variable resistor from an output pin. We've configured this as a high ouput. The overall resistance of the POT...
Hi,
I'm testing ads1292 sensor with nrf52832.
I got some problem when i use spi manager library.
I'm using ble_app_hrs project.
If i use spi manager without advertising...
Hi,
We build a new board based on nRF52833 wlcsp,
I tried to run a simple code with BLE peripheral (ble_app_uart example), and I noticed that the HFCLK is not working...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi
I am running this example from SDK 15.2.0.
I am trying to figure out how the server knows at the end of the session how many bytes of data the Peer received.
Anyone...
The information on the website currently only supports nrf52840.
Can nrf52833 support DFU over USB?
If yes.Which example can be used? Does it use the same DFU USB bootloader...
Hello, I am studying the peripheral/ble_app_uart and peripheral/ble_app/template examples to understand the proper way to build a peripheral with our own set of services and...
Hi,
I have hard time to setup west in my Ubuntu PC. It was installed, but not fully working. So I tried to uninstall and reinstall, and also one time, I may have upgraded...
