The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello All,
I am interfacing WS2812 RGB ringx16 with nRF51822 and use nrf51-neopixel library from github.com/.../nrf51-neopixel
Its not working.
for example : value...
Hello,
I was looking into Gazell and read that Gazell only allows pairing when Host and Device are in close proximity to each other. This range is about 30 centimeters...
I'm trying to maximize BLE throughput between a central and peripheral (I'm programming both) running the new s132 SoftDevice v3.0. I can't achieve the maximum data payload...
I am trying to use the NRF51 dongle (PCA10000, firmware ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex) with the sniffer software but on selecting a sniff source and starting...
Hey,
I successfully build and load the ble_uart_pca10028_s130. Now i want to edit something to the Code and this error is shown up.
I think I have to include something...
Hi there, I have done search and know there are several similar questions, but unfortunately I didn't find any useful answer after carefully reading through them, thus I decide...
Hello,
I've just read the thread explaining the UART baudrate register settings. I then looked at the nrf52_bitfields.h file and found that the baudrate register values...
Hi ,
We are using Nordic SDK for our development and we have done some changes as per our requirements in the SDK . We are going to share the same with our end customer...
Is there any BLE chip under development which has lesser IO pins, as I feel most of the IO provided are underutilised.
I may be wrong or there might be technical issue...
hi,
i have a requirement to connect two nrf51(PCA10028) boards to connect each other.
1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth...
Hi,
I followed steps specified for development-with-gcc-and-eclipse using link
devzone.nordicsemi.com/.../
Following are the snapshots of my development environment...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform. Specifically using it a Central role to connect to a commercial Blood Pressure peripheral...
As far as I understand the nrf51822 has only 1 hardware uart. I want to communicate with the esp8266 over uart using standard AT commands, but still retain debugging possibilities...
