I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi
I am developing a bootloader for nRF52840 using SDK 15.2.0 and s140_nrf52_6.1.0_softdevice, that should support both USBD and BLE transports.
The first transport layer...
We are using NRF52840 with Softdevice 340 and several sensors connected via ANT and BLE. NRF is connected to STM32 via serial UART connection and use ANT serial protocol for...
I am using PPK to measure current. The system uses 2 CR2430 in parallel.
I observe that
1. When using the battery as external supply, the battery voltage drop to 2.5V...
I am using the original board. It does not have a 32kHz crystal.
So I want to use the built-in RC oscillator.
In addition, use the time example of nRF5_SDK_16.0.0. "NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I am using nRF52840 S140 v7.0.1. I have few queries on DTM functionality.
1) As per standards, we can do DTM test either by sending HCI commands or UART commands...
Hi,
Using Eddystone example I configured EID and TLM slots. I see in nRF connect app both EID and encrypted TLM(encrypted data, salt, MIC).
How to exactly decode the...
Hello,
we are experimenting with the Nrf52811 CTE feature and have a few doubts concerning the documentation. We program our experiments with bare-metal (no soft device...
Hi,
I am working on one business use case. The basic requirement is to monitor the outdoor air environment from different locations. I want to try out the initial things...
Hi,
For nRF52840 BLE, in the DFU (OTA) example (buttonless OTA):
../nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_buttonless_dfu
How scanning is done? Or where...
Hello, I'm using Zigbee SDK 4.0.0 with Segger Embedded Studio 4.30 and custom pca10059-compatible debug board.
I ran into difficulties when trying to subscribe to attributes...
Hi,
I am using custom gatt service & I have included some of the code which supports swift pairing from ble_hid_mouse example. Here is my sniffer log -
& the jlink rtt...
