Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I have two nrf52832 boards. One as mater and other as slave. I'm trying to develop a communication between master and slave through ble. Also i need to connect the master...
Hello, can someone tell me how I can change this, as shown in the picture?
Strangely, I have already selected the proper target device, as shown in this pic:
What...
I want to use UART to read GPS data while advertising.
After I add uart function to ble_beacon_example, UART API app_uart_get() always return NRF_ERROR_NOT_FOUND.What can...
Hi,
Can Anyone has experienced with nRF52 PWM clock generation ? I am trying to generate 8-Mhz clock out of GPIO by configuring it for PWM module.. But so far I can get...
I have taken ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0 and i integrated Alert Notification Service,DIS[device information service] and DFU... Device...
I'm using the latest version of Keil with Software Packs. As I understood, copies of configurable files are stored in RTE folder. Non-configurable files are stored inside...
When i connect the board to pc its not detected and No J-link device in device manager
But when i press and hold the IF BOOT/RESET button and power cycle the board the LED5...
Hi,
I want to advertise the beacon with its name visible using the ble_app_beacon example but not able to understand how to proceed.
With this, I am not getting how can...
I want to make the led ON always and making the source code from scratch in keil mu vision 5. I am not able to understand which library is to used and how to proceed.
I'm using nRF51822 to communicate with nRF24L01+ without SoftDevice, and it is working fine.
But when I add app_timer.c to the project and compile, it will show the following...
Hi,
I am able to program my custom board using nrf52dk (only 32 Mhz osc populated on custom board), and I can also see the output of SEGGER_RTT_WriteString() though JLinkRTTClient...
We've been suffering Unreliable Auto Connection for quite a while... "autoConnect" sometimes just doesn't work to get the device back to connection. Below is the failure message...
Hello,
I started with example apps and have got one working with the supplied makefiles, gcc, and Eclipse. I'm able to debug my code without trouble, and have succeeded...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
