Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi guys,
I am trying to create a Dual bank DFU bootloader (BL) program for nRF51822 which will be able to update the SoftDevice and bootloader no matter if the "Enable...
Hi,
Sorry if the answer is obvious but I'm not getting it :-)
I looked at ble_app_uart, more specifically the uart_event_handle function and its interactions with app_uart_fifo...
I want to access an SPI-only sensor device from a Blend Micro.
There is a need to avoid collisions between the two uses of the SPI port for the sensor and the nRF chip...
I just made it to upload the example to the device. I'm new into firmware development btw.
I changed the timeout so the beacon will stop advertising after 120 seconds but...
Hello, I have implemented the code below for my project
based on switching central and peripheral role in S130.
The code works fine on the Devkit PCA10028 but on porting...
In compatibility matrix it is shown that s110 v 7.3.0 is compatible with nrf51422 when using SDK 7.x.x. But when I downloaded s110 v7.3.0 in its name and specification documents...
I tried to build the example project "ble_app_uart" bundled with nRF5 SDK (nRF5_SDK_11.0.0_89a8197) within the MDK-Lite V5.18K. It failed and I got the following messages...
Hi!
I am attempting to flash sdk11 examples onto a QFAB board compiled using arm-gcc over JLINK SWD p20 via the NRF-51DK.
While running make flash, the nrfjprog command...
Hello I found example for dual bank bootloader ("examples\dfu\bootloader\pca10040\dual_bank_ble_s132"). And it works well.
Do you plan also to add a SINGLE bank boot-loader...
hi all,
I am using SDK version 8.
i want to make button as ON and off switch.
REQUIREMENT:
When button is pressed counter should keep on incrementing when i released...
Hello,
I would like to simulate the spreading of a disease using the nrf51822 beacons. My question is if my envisioned project is possible as I'm completly new to nrf51822...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
