It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
Hello. We have product based on NRF51822 chip. 24 bit 4 channel ADC connected through SPI to MCU. Data rate is 250 Hz (4 ms). We send two ADC samples evry notification packet...
I started setting up Zephyr SDK development on my W10 laptop, according to the nRF Connect for Desktop guide, but running into this error when executing pip requirements installation...
Hello,
I'm writing a BLE app that acts as a peripheral and a broadcaster. If a connection is established, I'd like to continue advertising but update the advertising parameters...
Hi,
I am migrating sdk 15.2 to 15.3. Everything works fine, except the nrf logging. Currently, I am using RTT configuration, with default backend enabled. The code is simple...
