Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi,
I have some question below: note: the project_uuid belong uuid-16bit by my define uuid of product myself.
1. My project uses project_uuid and DFU_btn_less services...
Hi i'm first in BLE
I use nRF52840 DK and SDK15.3.0 and SEGGER embeded
when I excute single example(ble_app_blinky, ble_uart, timer), it has no problem.
but when I merging...
My UART is going into a NO_MEMORY error after trying to transmit a single byte. When i try and put the second letter on the transmit buffer, it gives err_code = 4. I tried...
Hi Everybody
When I run my code with the debugger, it always crashes when executing sd_softdevice_enable(). Even if there is no breakpoint activated. However, when I run...
SDK 15.3 API S132
How can i implement the HFCLK using softdevice or how can i enabled it
I need to be able to run an SK6812 which has the following timing requirements...
I'm attempting to make a custom program using a few different libraries based on the samples. In attempting to initialize nvs, it returns -22. I've been able to trace it deep...
Why does " app:" appear in my serial port when reading from ble_app_hrs_c from the SDK for nrf52dk. I was looking to remove this part sending to the com port but I cannot...
Hello to all,
We have developed our application & the following platform we are using:
SDK 15.0, Segger IDE on windows PC
Softdevice version is 6.0.0
Hardware version...
Hello,
I'm using SDK15.3.0, softdevice S132 v6.1.1 and we would like to know if it is possible to combine the application and the bootloader in the same ZIP file in order...
Are the MIPI and MAGPIO interfaces mutually exclusive, or is it possible to setup nRF9160 to use both? For instance, can I use MIPI to control RF switches, but at the same...
Hi,
I've created a project combining gps, nvs, and mqtt based off the nrf and zephyr project samples. I've been able to go into the sample projects and add .overlay files...
Hi.
I'm dfu test for sdk13.
NRF52832 EVM board
nrfutil version : nrfutil version 3.2.0
D:\nordic_nrf52832>**nrfutil.exe dfu ble -ic NRF52 -f -pkg dfu_test_app_hrm_s132...
Hi, i want to use dfu for application with mesh. But i want to update via ble in direct connection with phone, not via mesh protocol. Should i use example from mesh sdk or...
nrf52832 is connected to the main controller of the circuit on uart lines (RX and TX).
We have observed that even when we completely cut-off the power of nrf52832 then also...
