I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
We are using the nRF52832 with S332 v2.0 of the stack. We have recently been testing concurrent operation of a BLE peripheral connection and an ANT bidirectional master. The...
Hi all,
I'm using nRF52840 Development Kit and Nordic SDK v15.2.0 with soft device v6.1.0
I'm using ECDSA Cryptographic libraries for a BLE related project. I want to...
Hello,
I am working on Low power and Ultra Low power.
I am using the nrf52832 chip as well as the breakout board. In SYSTEM-ON mode power consumption around 6 mA and in...
How do I calculate round trip delay (time taken for packet to travel from peripheral to central(PC) to peripheral again)? Is the existing time calculation in the example code...
Hi,
I have some troubles using TWI easy DMA. I set EASY_DMA flag to 1, but I can't see any results in my performance tests. Can anyone explain me the required steps? ...
I am looking at the android version of the Blinky application and was trying to make some modifications to enable the LED3 on multiple boards (peripherals) to turn on from...
Hi,
In a peripheral, a notification is sent to the central every 10ms. (payload less than 20 bytes)
I use : radio_notification_init(6,NRF_RADIO_NOTIFICATION_TYPE_INT_ON_ACTIVE...
i want to read the temperature ..... my temperature data is executing from 0 degree temperature ...is there any way to execute only actual data instead of starting from 0...
I'm probably not using the good terminology here... let me explain my application.
I have an existing board which has all the logic implemented in an STM32 MCU. I now need...
Using Softdevice 132 version 6.1.0 I issue the request for scanning by calling sd_ble_gap_scan_start() with: ble_gap_scan_params_t scan_params = { { .extended = 0, .report_incomplete_evts...
Hi all,
I want to measure higher frequency (8 MHz) count/ticks by using the lower frequency (32 KHz) is there is any method to do it or any examples.
I want to measure...
Hi,
I am evaluating the nRF52840 with the Segger IDE.
I am about to experiment with Bluetooth, but I have a hard time understanding the different protocols/softdevices...
Hi, recently I've been confronted with this issue that all of my stocked nRF52832 ICs would not work with the lastest SDK, which later turned out to be engineering samples...
In the light of recent news like this one, https://arstechnica.com/information-technology/2018/11/bluetooth-bugs-bite-millions-of-wi-fi-aps-from-cisco-meraki-and-aruba/ ,...
if m_replay_cache[ivi][i].seqno == 0xFFFFFF, then new message received and seqno == 0 or other value, Whether the message is valid ?
Because the seqno of the new message...
