Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
What is the power consumption to check battery level?
How quickly at boot time is an accurate battery state of charge available?
What is the RDSon in the path from VBUS...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
HI,
I have a product which scan for RFID card through NFC and Mobile Device through BLE after nRF52840 MCU was wakeup.
If I scan NFC and BLE scanning separately, everything...
Working with a Pinnacle 100 using an NRF52840. I have a HMI with a TTL serial interface. I have verified I/O on the HMI itself via a TTL/USB converter to Tera term, but having...
Hi! I have a fleet of narrowband and cat-m devices around the world. I want to determine their rough position by using the cell tower information. I tried CellLocate from...
I have a board with the nRF52832 and a board with 12 SK6812 LEDs on it in the shape of a ring. I have code that sometimes will display the correct color on the ring but other...
I think the NFC pin is set to the default state on the nRF52832.
Currently, I set CONFIG_NFCT_PINS_AS_GPIOS to 1 to use it as a GPIO pin, but is there a way to make it the...
Hi, I'm using nrf52810 ,nrf connect, zephyr, vscode extension. I’m having trouble using both UART0 and the NUS UART service. Here’s a snippet from my overlay file:
/ ...
Hello everyone, I'm trying to perform a device firmware update using the buttonless service on nRF52DK with SDK v17.1.0 and Softdevice S132.
I can connect correctly to my...
Hi,
I’m working with Timer 0 on my nRF5340 DK and trying to set up two different intervals: one at 1 second and another at 60 seconds, each on separate channels (COMPARE0...
If I am to do a custom SPI Slave driver to achieve ultra low latency handling and would like it to coexist with NCS / Zephyr, is there a document describing this ?
E.g....
