I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
We are working on a asset tracking device which will operate with a 3V CR2016 (85mAh) coin cell battery or smaller.
Per our understanding, the max interval of S110 softdevice...
I am using nRF51822 with S130 stack.
Some of my flash write works fine, some return NRF_ERROR_INVALID_ADDR,
I could not figure out exact cause, all my addres is word-aligned...
Hello,
I know this issue has been discussed several times on the Dev Zone, but in every post, i found the same answer and this answer does not help me.
As I read, intalling...
Hello.
I try to build small network: 1 central device (CD), several relay devices (RD), several broadcast devices (ED). CD and RD have to receive commands all the time...
I am using adv_report_parse to try and return the device names the scanner picks up. However it returns some bizarre charters after the name....
it should read P Device...
hello,
Please forgive me if I am asking a stupid question.
I was editing S130 demo app and I included pstorage.c file to the project. while compiling it is showing error...
I have compiled my mbed program and hex file has been downloaded but I am unable to drag and drop my hex file to mbed USB drive. It is saying Not Ejected properly. I tried...
I am following app note nAN-29 "nRF51 Development with GCC and Eclipse Application Note v1.1". In the section "Flash download" there is mention of an executable called nrfjprog...
Hi
I use the PORT EVENT to produce multiple interrupts.But I have a question by these:
NRF_GPIO->PIN_CNF[BUTTON1] =
(GPIO_PIN_CNF_SENSE_Low << GPIO_PIN_CNF_SENSE_Pos...
Hi,
have some of you expierence with profiling on a nrf51422? I think what would be nessesary, is at least one high priority timer, to sample the program counter, some kind...
Hi,
I’ trying to save some user configuration data on the NRF51822 Flash using pstorage module.
Below is the code that I wrote, the code runs on the board with no error...
I have two boards based on nRF51822 parts:
Nordic dev kit PCA10005 Rev 2.2.0 2014.14, chip marked N51822-QFAAG0-1351AG
Custom board with Fujitsu MBH7BLZ02-109004...
I'm getting an error which says the identifier ble_temperature_t is undefined, and it is showing as an error in the keil (unkown type name). However when I click on the variable...
Hi everybody,
I just received the nRF51822 EK and as I was starting to set it up I ran into this. It took me a while to figure it out but when trying lo load the blinky...
