Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
my setup is the following:
- SDK 2.6.3
- nRF5340
- Low power management for external flash enabled
- Logging enabled (based on littleFS)
- external flash used...
Hello,
I’m wondering if there is a way to forward data from RTT to a COM port on Windows.
I’m currently evaluating the GPS performance of my custom PCB using the GNSS...
I have a very simple product which consists in a Xiao Nrf52840 board (which is FCC certified) wired to a 5v relay module. I was wondering if I would need additional FCC certification...
Hello, I am trying to add GPS functionality to my program running on the Thingy:91. However, I can't find any examples except for the Asset Tracker, which seems overly complex...
Hi,
MCU - nRF52832
I am trying to understand the power consumed during the PaWR operation. I am referring to the steps explained here: I am getting the a similar graph...
We currently have several nRF52840-based devices deployed in the field, running firmware developed using the nRF5 SDK and utilizing the SoftDevice S140 for BLE functionality...
Hi Team, I am trying to see the PaWR PDUs in wireshark sniffer. I am using example periodic_adv_rsp from NCS v2.9.0. I am referring to the link for exploring. How can I see...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
