Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
Hi!
I am using the nRF52832 for a small custom PCB for a wearable device and I would appreciate a review from the experts, before proceeding with manufacturing :)
The...
Hi,
I have a FAT file system that I use with an USB Mass Storage feature. I use the mx25r64 NOR flash (the same as the nrf7002dk evalboard). I am working on ncs 3.0.2. ...
TLDR:
I'm working on getting LE Audio working on a Raspberry Pi CM4 setup and running into some frustrating issues. I've got a u-blox NORA-B126 module (with the nRF5340...
Hi nordic engineer
I have a product use nrf52832. And have two project,project use nrf5 17.0.0 SDK and MDK.
The project A choose chip nrf52832 and S132
The project B...
Hi
The nRF54L15-DK suite tests the accuracy of channel sounding, all ncs versions are v3.1.1. I am using the channel_sounding_ras_initiator and channel_sounding_ras_reflector...
Hello,
At my company, I am working on a board with an nrf54L15, equipped with an SX1261 and an ADC MCP3461R.
I started development with SDK 3.0.2 and everything is working...
Hello!
With nRF52, nRF5 SDK and SoftDevice S130, we were using some of the Radio's PPI events (e.g. EVENT_END) for some functionality.
Now we plan to move to nRF54L and...
When running the channel sounding example on the nrf54l15, how can one obtain the IQ values of the ranging signal?I want to obtain the IQ value and then use my own algorithm...
Hello,
I have tested a thread network with a nRF52840 SDK programmed with Thread COAP Client sample and two nRF52840SDK programmed with Thread COAP Server sample.
All...
I've built a project based on the peripheral_uart appliction. This is working well, but I need to now sort out the lowpower mode. My product is battery powere & I need to...
I’m using the nRF54L15 to test throughput. I want to connect a single board to any arbitrary BLE device to test GATT throughput. Is there any way to do this? Are there any...
