Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
I need to sample ultrasonic signal with PDM microphone. I would like to use NRF52840 PDM module and configure it for sampling frequency of 96KHz. Is it possible? Also...
Hi,
I have used BMD301 BLE chip. I have connected one wifi chip "ESP02" with BMD301 chip via UART.
I am using nRF5_SDK_15.3.0_59ac345 for my ble application firmware...
Hi,
we have a nRF52 DK getting sensor values from a Sensor connected as SPI-Slave. Everytime there is a new Sensor Value (~20 ms) the sensor generates an Interrupt and pulls...
Hi,
While upmerging our project from SDK 15.3.0 to 17.0.0 we faced an issue in the sdc_handler due to usage of a NULL pointer.
In the case SDC_EVT_INIT if the p_event...
Hello,
I am experimenting with PWM for time, I have a setup where I am using three sensor which gives analogue output.
I am using a mux which has two control pins, so...
Hi all
I have just started doing some work with the nRF52840- DONGLE (and hence nRF52840-DK) and am new to Nordic devices, tools, BLE, etc.
Basically for my first application...
I'm attempting to increase the size of the TX Queue in an effort to increase notification performance.
I'm using nRF52840 with an S140 soft device. I use Segger Embedded...
Hi,
I have two nRF9160DKs and I noticed that the SHA-256 digest of the credentials looks very strange
Questions:
1, Why are the digest so repeating? I have installed...
I'm implementing the door lock cluster on the server side (the door lock device), and needs to send event commands to the client (door lock controller/gateway) . According...
Hi Team,
We are using the NRF52832 for our application and we have enabled the crypto libraries for that.
For,
1. AES-ECB,CFG,CBC modules we are using the "mbed TLS...
Hello,
We are using nRF52840 with SDK 15.2.0. In our software we have handled the DTM and we are able to send the commands using UART.
We would like to do the receiver...
Hi,
I'm developing a Bootloader for the nRF52xx chip using the SoftDevice S113 v7.0.1 and SDK v17.0.0
Looking into the infocenter I've seen that there's a possible mistake...
