Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
Hi Team,
We are using nrf9160-DK. We have tested assert tracker application, where we got the real time GPS data(DK location) we are happy with that. We also tested the...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Environment :
Host : Macbook Catalina
SDK : 16.0.0
Toolchain : ...2018-q2... (the pre-configured toolchain in the SDK)
SoftDevice: (not used yet, planning to use...
Hi, I'm using mesh_ SDK and nrf52840, I want to know whether the relay node in a BLE Mesh can wake up at a specified time to receive or send packets, and sleep the rest of...
Hi,
I am developing a device based on nrf52840 soc, and the rule of my device is peripheral. I want to know, if a connection was established, could my device start the...
Hello,
we are currently in the development of a low power, battery powered device that needs to count slow pulses (period between ~10ms and several seconds).
At the...
I have a custom nRF52840 board that transmits sensor data (using UART) to a PC with an embedded Bluetooth adapter. I have a code on Matlab that works just fine (using blelist...
Dear Sir.
I am using Master SPI to drive 2 slaves.
Both spi are referenced within Interrupt routine ,
When both spi;s slave are referenced I get an error
err = spi_transceive...
This question has been asked before. I have been using the previous threads to cobble together what is below. I opened a new ticket as reopening (really) old threads is generally...
usb hid how to send 6 bytes of data, app_usbd_hid_kbd_key_control can only send 1 key value, I see that app_usbd_hid_kbd_ctx_t can fill 6 bytes, please see
typedef struct...
Hello,
We're needing a lot more RAM than what nRF91 has, does current nRF Connect SDK support parallel PSRAM on Zephyr somehow or is the development on a roadmap?
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
