Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hi,
I already read all the forum posts about this buffer order swap problem of the SAADC. Especially this one: https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in...
I'm upgrading a big project from SDK 6.0 to SDK 12.3, everything's going well, but I had to comment out a library because in SDK 6.0 the previous developer uses the input...
Hello there
I am trying to program the BL651 wich makes use of nRF52810 chip, however i haven't been able to program it.
The tool im using for the task is the J-Link...
from SDK 3.1 for thread and zigbee in simple coap server
after any time it go to disabled mode and no response
what means the flags? why is it disabled and do not...
Hi,
I want to create my own bootloader for the nrf52810. If i don't want to update my softdevice i just put my bootloader code just after my softdevice.
But it is not...
Hi everyone, I am wondering if there exist any list of Known Issues for SoftDevice S130 v2.0.1. I looked into the release notes published in PDF along with the hex files,...
Hi
I have a question about the new chip nRF52811, it supports AoA direction finding, but it doesn't support Bluetooth mesh?
There's no chip can support both AoA and mesh...
Hello,
I am using the nRF24L01 + circuit on a PCB made according to reference design.
Can I use a 0.5 or 0.6 mm thick PCB? Reference design is made on 1.6mm PCB thick.
I'd like to sniff the BT packets between a remote control and a bed (which is controlled through BT4.2), in order to control the bed through an android application.
Can...
I am using uart to transfer data in a while loop, and it works fine. Now I want CPU to go to sleep mode with sd_app_evt_wait(), and CPU to be waken up via Button then receive...
Hello
I'm working on Smart Remote custom board, which is based on nRF52832.
My Setup is running very well but only when RTT Viewer is connected.(and advertising led is...
I am using the TWI peripheral and want the clock frequency to be 400kHz.
In the data sheet it says for the register setting: 0x06680000 = 400kbps (actual rate 410.256 kps...
Hello All,
I am Facing issue in advertising custom board NRF52810.
I am trying to do the led blinking program on above board.
Using the SDK 15.3 with S112 . The hex...
In Nrf5 sdk V15 their is a micro
ticks = APP_TIMER_TICKS (MS);
My question is what is the maximum value of ms which can be used as input.
the same question goes to the...
Hi, I'm looking for information about duration of peak current on BLE and NFC mode on nRF52840.
Do someone have any answers ?
I saw that peak current on NFC is 80mA max...
