Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I have just received a set of nRF52840 dongles and I want to write applications that run on the PC using the dongle so I have downlaoded the pre-compiled pc-ble-driver located...
Hello, I am using SDK version 15.3 and nRF5280DK.
I am having trouble finding an example that uses the button handling library .
From the information I could find on the...
I've been trying to connect my device to AWS IoT for a week, but I'm getting the same error "no matter what" I do (ERROR: mqtt_connect -45), which seemingly is an authorization...
Hi! We're developing on an nrf52840dk and have been running in to some problems when we want the system to only pull currents in the size of a few microamps. As our system...
hi, i'd like to make communicate 2 different nrf24l01+ without the enhanced shockburst if possible, i'm using arduino to control the tx and fpga to control the rx; i'd like...
Hello!
I am trying to improve the GPS-performance of our custom board. It is difficult to know if it is my hardware, firmware, antenna or something else that needs to be...
Hello, im relatively new to this and not sure why im getting this error. According to previous such error clarifications, i read that the newest versions have to be used....
Hi I have a couple of Thingy:91 devices, which we are using to evaluate the 9601 SoM.
The devices ran out of credit, but after buying more iBasis credit still would not...
Good afternoon. I use NRF 51822, and I want to use RTC 0 or RTC 1. But there are problems, if I do not initialize BLE then the compiler does not execute LFCLK_config because...
We are now developing BLE ADC sender, using nRF5_SDK_14.0.0_3bcc1f7, and two nRF528322s (sender and reciever).
We send SAADC data via BLE, after that, we disconnect, and...
I am currently using SysTick to count milliseconds in my device. This works fine, however with it enabled I can't sleep the device as it wakes up instantly.
I have tried...
Hi,
I'm not sure if I'm doing something wrong so I'm hoping someone can help me. After updating from 0.11.4 to 0.12.0 of pc-ble-python-py, I get the following error. I've...
Hi,
Please help to suggest if 10K Nodes in a single network with 100 Kbps data rate is achievable with data transmission interval being roughly every 30 seconds.
This...
I have the debug section of the evaluation board turned off, modifications to measure current with a DMM set up, and am using a keysight 34465a DMM to measure current. The...
