Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
We have our own custom board using nRF52832 (via Laird BL652 module). Until recently, we have been programming our application, bootloader and softdevice using the PCA10040...
SDK12 and SD 132 v3.
I have my code working for HVX from the peripheral. I can HVX send up to 80 bytes on one characteristic in one call (ATT MTU was set to 83 and DLE...
The NRF52 product spec suggests:
"The input buffer of a GPIO pin can be disconnected from the pin to enable power savings"
I've found that gpio.h provides the function...
Here is a snippet of my debug log:
nrf_sdh_freertos: Creating a SoftDevice task.
nrf_sdh_freertos: SoftDevice task not created.
app: ERROR 4 [NRF_ERROR_NO_MEM] at ...
When using radio notifications, there are a few compiler warnings.
Compiling file: ble_radio_notification.c
../../../../nRF5_SDK_14.2.0_17b948a/components/ble/ble_radio_notification...
I've been working with an Adafruit NRF52 Feather board for the last week, and have been struggling to get the board to go into a low power mode. At the moment, I am working...
Are there any publications, from Nordic or academia, that give estimates on what would be the maximum capacity of a BLE mesh network?
I believe there is a hard limit of...
I have created a program on Arduino which does audio/video output and takes input from accelerometer and camera module. I was able to move accelerometer code to NRF52 with...
Hello guys,
My set up is pca10028, s110, sdk 6, tablet with nrf_connect app. I am using modified ble_app_uart example. I was trying to send >20 bytes from nrf_connect app...
hello
Now i am useing the DK of nRF52832 and SDK14.0.0 of ble_app_uart.
I am experimenting to transmit data from external equipment to nRF 52832 and send data to smartphone...
Hi - I am trying to power the nrf52840 DK from a non-USB power source and it does not power up, or powers up and down immediately. I tried the coin battery (with SW9 to VDD...
I am working on a project where i need to send sensor values from nrf51822 module to a raspberry pi. The sensor values are received by the nrf using I2C protocol.
I am using...
I would like to get data from BLE device and I have two services are available in BLE device which is offering in 3 characteristics and 2 characteristics.
Can u share any...
I'm confused about the issue with using GPOPTE inputs in low power applications.
errata 97 indicates that GPIOTE should not be used in input mode
It was also discussed...
Hi,
When I build the SDK (14.0.0) with SOFTDEVICE_PRESENT and in sdk_config.h #define NRF_SDH_ENABLED 0 I get the following link error (using IAR:)
Error[Li005]: no...
