Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hello,
i decided i will use a nrf52 3rd party module for my project cause i want to skip Qualification Process and Bluetooth RF-PHY test.
I haven't seen any 3rd Party...
nrf52DK - SDK12.2
This is probably a simple thing I am missing but I can't seem to find the answer.
I have been following the tutorial for BLE Characteristics ( here...
Hi,
I am working with a nrf51822 and I have seen that the way to wake up from System Off mode is by a GPIO interrupt. I wanted to know if it is needed to configure previously...
I am a new to the uVision4 and having trouble with the 51822 evaluation kit demo.
I am able to build the ble_app_hrs demo and can load and run it using the Flash / Load...
Hi
I'm using fs_storage function to read and write in flash memory. Value successfully stored in evt->store.p_data but after power off it value become 0
switch(evt-...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
Hello,
i use a nrf52 developpment board, with the SDK 12.1.0. I use the ADC example which use the ppi channel, my question is : it's possible to set the ADC driver without...
Hi all,
i try to log event in memory, and when connection is established read value from E2C and send to APP.
if i send characteristics when event BLE_GAP_EVT_CONNECTED...
I use the ble_app_proximity example of the nRF51_SDK_10.0.0_dc26b5e, the chip on my board is QFAAH00 . When I down load the code, it pops the windows "IAR Warning: Stack pointer...
I am learning BLE and trying to develop a Health Thermometer which can be seen in the nRF Toolbox
I am using Bluetooth Developer Studio but cannot get the nRF Health thermometer...
In SDK 11.0 it seems that in case pin 31 is configured as a button (using port events), nrf_gpiote_task_enable keeps triggering the port event due too a work around for OUTINIT...
I developing wearable product based on nrf52832. The product is act as a beacon and its location track by other fixed BLE readers to positioning it in particular defined area...
Hi,
I'm working on accelerometer + BLE application. My current configurations are nrf51822 and LIS3dh accelerometer chip, Protocol TWI, Softdevice 110, BLE service type...
Hi!
I'm trying to learn osTimerStart(), \ble_app_hrs_rtx.
Compiling was successful, and it is working.
If I set the timer interval shorter than 25 ms, the timer cycle becomes...
