I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I've just got up and running with the nRF51 DK. I've had a play with some of the examples, and now I've started on my own project using ble_app_template_s110_pca10028 as a...
After startup, I was able to send a spi msg from the master (app chip) to the slave(nordic). But when I try to sent the second message, I did not get any response from the...
I am using the SPI Slave peripheral and attempting to send the nrf51822 bytes from another MCU.
Am I right to assume that there is, basically, a 256 byte max per transaction...
Hi,
I have nRF51822 board which works great with my app when running on iOS 7
The application listens for iBeacon transmission and displays them.
When i installed my...
Hi, I made a custom PCB.
I use a Revision 2 MCU.
The antenna is printed. I didn't used the chip antenna.
Sorry for not showing both the full schematic and the...
Dear all,
I'm trying to connect the NRF51-DK (PCA10028) with a LSM330DLC accelerometer over TWI (I2C). I'm using the ble_app_uart example, included the twi_master.h file...
I need to implement a function to store some parameters such as uart baud rate and use these parameter for device initialization, The parameter could be modified when the...
Hello,
I`ve got a working S120 peripheral BLE device with custom services and characteristics.
I am able to connect and bond with iOS and Android. But I cannot connect...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
