Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hello,
In the following code, I have tried to assign a channel to be asychronous so that I can transmit 8 byte acknowledged messages immediately following a button press...
Hi Support team,
I've ported succesfully chibios RTOS on the nrf51422 for month. I've also ported some drivers like I2C - UART - SPI- GPIOS and others... I can play with...
Hi, I have the nrf6310 code in C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\s110 and then i need use this code in the board PCA20006 (Smart beacon).
Do you know how...
hello Nordics,
i am trying to configure 1ms timer along with BLE_STACK is enable
and same time i am sending 3byte data for every 500ms . and 1ms timer is very important...
I need to automate OTA updating the bootloader and radio for several hundred units that have an nRF51 (softdevice 7.1.0) from a VB.NET windows application. I'm able to call...
Hi, I just bough a couple of dongles (nRF51422_xxAA, with 16kB RAM afaik). In Pack installer there is a lot of example for the nRF51 series but all of them are for nRF51522_xxAC...
Hi,
I have a scenario where we may want a peripheral (using S110 softdevice) to switch connections between 2 centrals, depending on whether the centrals are present or...
Hi,
I am using the sofdevice s110. I want to encrypt my manufacturer_data. However , the type of the advertising is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND.
I tried : nrf_ecb_init...
Hi,
I use an NRF51822 eval board.
Recently i buy a module RFD22301. But it is programmed to be used with RFduino.
How I can program it to use the nordic Nrf51822 basic...
hi!,
I am configuring connection interval time is 7.5ms ,
and slave latency is zero.and every connection interval event I am sending 1 packets (and my data lenth is only...
I'm new to nordic. I am using Nordic DK (PCA 10028) and was able to flash the heart rate example on to the board and see it on my iOS device. I'm trying to test the uart sample...
I'm trying to install nordic SDK for Keil 5.13, but this is what the 'install.bat' says when I open it inside the directory containing 'PackInstaller.exe':
Please wait...
Hello,
I am interested in "nRF51 Smart Remote 2". As I have read in Product Brief it supports feature "Voice Command Features". But I couldn't find any information about...
Hello,
I have an application in which the available power is so extremely limited that the hardware cannot do anything else at the same time as conencting to a central...
