Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello,
I am using nRF52832 EVM board with SDK 15.3.0 in SEGGER studio IDE, win 10.
When I am implementing sd_nvic_SystemReset(); in my code, that time i am not able to...
I have a custom board based on QIAA Reference Layout 1.1 Variant 6.
The application is built with Zephyr without bootloader and is placed directly on address 0x0.
When...
Hi, I'm designing nRF52832 custom board, on 'single side' pcb.
To make VDD and GND lines connect, I used 4 jumpers, which have 0 ohms.
I designed with nRF52832-QFAB reference...
I used the ble_app_uart for pca10040e successfully on the DK52, now I'm trying to port that project onto actual nRF52810 chip.
This is my build configuration on SES (Segger...
Hello Nordic Support Team,
The question I have is simple.
Can I use the pc-ble-driver with the ble_connectivity_s140_usb_hci example found in SDK15.3.0?
If not why?...
Is there any public documentation on the LTE Modem hardware API for the nRF9160?
I'm interested in porting an embedded operating system written in Rust to the nRF9160 and...
Hi,
I am using ncs 1.0.0 in nRF9160.
I have enabled UART 2 interrupt during initialization of the uart as below and it works fine.
To reduce the power consumption...
Hi,
Using the Thingy app on my iPhone works fine.
However, I would like using my iPhone as a gateway (thingy:52 -> iPhone (BLE -> Internet) -> nrFCloud. I installed the...
Hi,
I'm migrating a project from SDK 14.2 to 15.3 and I wanted to use the generic and "full" sdk_config.h located in config/nrf52840/config/.
The documentation says...
Hi everyone, I would like to confirm if this is a bug.
Per the comment, it seems that the intent of the code is to reject an attempted SoftDevice update.
However, this...
Hi,
We're currently developing nRF52832 module which can support for several products, like bulbs, switches and etc. Once we finish the developments we're try to make them...
Hi,
The final design we are working on is composed of 8 peripherals notifying (every 80ms or 160ms) to 1 central.
Packet data size is 141 bytes and depending on rate configured...
Hello,
I currently have a working BLE application for the nrf52810 which is currently using the s112 softdevice. However I wanted to increase my BLE throughput so the s113...
Good morning
Our company is using nrf52840 devices with BLE-mesh and asked me if I could have a look at the Zigbee functionality for adding Alexa compatability.
So...
