I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
We are currently running on mfw_nrf9160_1.0.1 and NRF master as of today (Sept 13, commit 224bee9).
We are developing an MQTT application that uses TLS mode sockets.
We...
52832 & s112 & sd6.0 & sdk15.0
If you have multiple pairings on the same host will return error by “pm_device_identities_list_set”
err_code = BLE_ERROR_GAP_DEVICE_IDENTITIES_DUPLICATE...
Hello everyone,
I trying my nrf52832 getting ultra low power current conception mode using System OFF mode (0.3uA). I using SDK 15.2 ble_app_beacon example I change 32KHZ...
I started developing on the Adafruit nRF52 module. I wanted to make a custom PCB to demonstrate a prototype and fabricated a board with a MDBT42Q module from Raytac. I sent...
Hello, I have used the nrf52840 . I have created applicaction from existing examples of SDK which used bluetooth. And now want to add OTA via bluetooth. Is it possible use...
Hi,
I am developing an app based on PCA10059 dongle. my program work fine on this dongle, but i have a problem with it. after programming PCA10059 dongle with my firmware...
Like the title,
Is it possible to disconnect ble link or stop advertising at runtime, then change the service uuid and characteristics?
I wanna to do OTA service in application...
I am able to receive motion data [rawdata] from thingy52 on my RPi 4 using bluepy library in Python3.
I want to extract the raw values of Gyro/Accl/Mag from sensor.
The...
Hi,
I'm writing a program that swaps between LTE and GPS to send the device's location to AWS over MQTT. I am able to connect to LTE and AWS, then swap to GPS and get a...
Hello. I 've got such problem with flashing some of the ESB protocol examples of NRF5 SDK. I use Adafruit Feather NRF52832 board with ST-LINK V2 debugger. https://www.adafruit...
I want to implement UART service which can act as central and peripheral at at time.
I am using nrf52832 board and sdk 15.
I tried to implement it by changing the services...
Hi,
I am following the nRF_Sniffer_UG_v2.2.pdf to setup the nrfSniffer. Wireshark does not show me my board among the interfaces. I had a look at the troubleshooting part...
Hi,
We are developing a Bluetooth 2d-3d mouse with OTA -DFU service.
The controller we are using NRF52832 QFABB0 it contain 32KB RAM and 256KB of flash memory.
SDK...
I try to add NUS service in example ble_app_hrs_rscs_relay.
I have fail on send data from "Relay" to smart phone iOS nRF Toolbox.
1. I have modify the MTU size . #define...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. The pins from the nrf52 SoC are all brought out on a female headers on a custom...
