hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
i’m using NRF52832 with SoftDevice S132 and Sdk 15.3 to develop a NUS peripheral and central. The system is tested as follows:
I have two NUS peripherals , a NUS...
Hello, I have questions about esim card.
1. Hardware footprint about esim chip.
I don't know which esim chip I will use.
So is there a common standard footprint?
If...
Hello,
I've a board with usb port
I can insert on USB the Raytac MDBT50Q-RX containing the nrf52840 and:
- my microcontroller can recognize it as CDC ACM USB serial...
Hi, I'm Developing Custom Board with nRF52832.
When I execute my custom code (by referring to ble_app_template example), an error occured.
First, my hardware spec below...
Hello, i am using the ble_app_beacon example on the nRF52840 DK with s140 and i want to send the service UUID for Device Information. I inserted the code from the ble_app_template...
i'm trying to get samples/drivers/CAN working with the nrf52
apparantly you need to enable CAN explicitly in menuconfig, which is already confusing because prj.conf has...
Hello. I met trouble, presented in the name of the thread. I use example for PCA10400e board. So, what I've changed to accelerate reproducing of this error. I change logger...
I have a question about the current consumption of GPIO and GPIOTE.
I want to use port in input configuration. Therefore, the following settings are made ("P_WUP_BLE"...
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes get an...
HI
We are developing a 2d-3d mouse .
We are trying to implement OTA-DFU into our custom board .
We first tried it on development kit and its working fine too . I can...
Hello all,
Environment:
Rpi with Raspbian Stretch (Release 9.8)
Kernel 4.14.8-v7+
Architecture armv7l
I have followed the below links to build BLE 6LoWPAN environment...
After compiling the SDK 15.2 ble_app_hrs_freertos_pca_10056_s14 example in Segger Embedded Studio there are a number of repeated warnings:
"configTICK_SOURCE" redefined...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
Hi,
I am trying to use the SSD1306 display with the nRF9160 DK.
I am using the code as is shown here
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples...
