hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
It seems I'm running into the fairly common "solution load command failed (1)" error on a nRF42840DK board.
The console output in Segger gives me the following:
...
Hi, I am using mesh sdk 3.20 and nrf52840.
I am using 3 nodes for testing. One generic on off client and two generic on off servers.
I believe that I have managed to get...
Hello, I am working on a project where I have 2 nRF52832 boards with the PCA10040. I have the example developer code examples. I am using the central and peripheral code examples...
Was looking through the reference designs you have in github .
I figured the difference between nRF52840_qiaa_var1 (what is qiaa ?) and nRF52840_qiaa_var2 is the use of...
Hello everyone,
I am facing an issue with UART communication from my nRF52832 to my GPS module.
I precise that communication in the other way works very well (I get...
We have a need to invert the TTL logic for the serial interface. All our "Unique" SWI serial interfaces use an inverted logic e.g. idle state 0 instead of idle state 1.
...
Is there any lnk which uses nrf52 mesh without models.
Means a simple function to send data(like "Hello world") to any node or group in Mesh.
and other node receive data...
Hello, I was wondering, Firstly and more important question, Is there a way in a BLE Mesh standard to physically locate/position the nodes? In order to obtain the distance...
Hello,
After (accidentally) entering bootloader mode on my nRF51 DK (PCA10028), the device doesnt show up either in the device manager or using nRFgo Studio (both not normally...
I bought Nordic nRF52840-DK at an electronics store in Taiwan. J-link cannot be detected when connecting to a computer. I bought two pieces nRF52840-DK. One of them can be...
I've been having lots of issues putting the example projects on the NRF9160 dev kit. It builds without errors, connects to J-Link, but sometimes fails on the download step...
I'm unable to program a nrf52840 dev kit (BMD340 dev kit) using the attached hex file combination of Bootloader and softdevice. Both bootloader and softdevice can be programmed...
Why do I get the folowing error with mbedtls when doing "west update"?
Possibly related issues: * devzone.nordicsemi.com/.../west-update-blocks-and-fails-on-mbedtls (Didn...
Hello All,
I loaded the last FW version (mfwnrf9160100) in my nRF9160 SDK using nRF Connect Programmer and looks fine.
However, the Reset button or AT commands are not...
How would I take a NRF51 Dongle that has the stock firmware from nRF Connect and communicate/send commands to it over something like PuTTY? I've tried sending AT Commands...
