Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
When i use nrfutil to perform DFU it is passed, but when i send it through STM32 dev kit it Hash validation failed. but however i can see the CRC is correct.
Hello,
I have an AMS AS7261 light sensor that I'm using with my NRF51422 DK to take a light reading, pull it using nrf_drv_twi_tx/rx, and send it over BLE. However, when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few variables in application. These will...
i have a complete project based the gfx project and i want to add BLE using UART for communication. i want to communicate my module with the nRF52840 dongle.
is there simple...
SDK14+NRF52832.
I used one timer to do something every millisecond. and I used another function to do a loop action, the function maybe breaked if the time period exceed...
Can not connect Android 8 mobile phones, such as HUAWEI Nova 3
Nodic equipment is not even found.
We cannot connect with official UART routines.（ble_app_uart...
I found a terminal that can not communicate with BLE. I think that the sequence after MTU exchange is strange. The program used is sample HRM. The terminal used is "Xperia...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello, I am using the nRF52840 dev kit. I am using SES to develop the code for it. I want to include the bosch bme680 library in my code. It comes as a libalgobsec.a file...
The objective is to have a device which constantly advertises some status information - this must be always visible to any Central in range.
The device may connect to at...
I inherited an active project with regrettably little support from the previous developer.
I have been trying to download a copy of the application firmware that I generated...
I try, DFU by USB-SERIAL on NRF52840-DK. I installed SoftDevice S140 V6.1.1 and open_bootloader/pca10056_usb (SDK15.3) Python2.7.16/nrfutil for windows was installed. My DFU...
I am trying to keep an output pin asserted while I jump to the DFU on the 52840.
We have a dead-man switch hooked up to pin 19. I need to hold this pin high while I jump...
So we are using NCPTransport from nrf-util (nordicsemi/thread/tncp.py) to have CoAP connectivity over Thread NCP from Raspberry Pi to other Thread devices. We have a use case...
Hi,
I am trying to install pc-ble-driver-py pypi lib into custom yocto setup. I have created recipes for it which is shown bellow
in python-pc-ble-driver-py.inc
...
