Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am having a strange issue with running BLE DFU on a project that I can't seem to work out. This an S132 v2 project with SDK11.
If all I do is program the softdevice and...
Hello,
I have read the questions on power optimizations in nrf chips:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I wanted to use SDK11 example ->...
Dear all,
I'm a quite new BLE stack user and need to get some idea on the idea behind service discovery.
I'm using the S130 and the BLE central example and want to read...
Hi,
We are going into mass production with our first product and would like some expert advice on what is the best approach.
1.) Since we would be doing production tests...
Question for anyone familiar with mBed code on nRF51 devices (I have cross posted on mBed, but trying my luck here too):
I'm developing an nRF51822 program using the nRF51...
Hello, I am trying to upload my custom firmware to the MetaWear RG (nrf51822) platform but currently without luck. Steps that I have performed:
Connected to the device...
Hi,
I want the bonding to happen between the nrf51 and the Android Phone by displaying passkey on the phone. This can be done using device manager or peer manager. When...
I haven't really found too much referencing how to setup an Eclipse DFU Bootloader project for Debugging.
What I know
To get the image to fit in the allocated memory...
HiNordic,
I found nrf5-sdk-for-eddystone Project in github,but it's just surpport nRF52832.I want to know where to find the nRF eddystone SDK which can surpport nRF51822...
We're working on getting our nRF52 app working with buttonless OTA updates and the bootloader. OTA works fine with the example bootloader, but when we extend our application...
Hi, I Converted experimental dual bank signed bootloader into single bank signed bootloader and it uploads the new firmware successfully but the problem I got is it erases...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
