Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
Hello,
We've heard that the BLE transmission packet length may be increased beyond the limit of 20 bytes in a future version of the S110 softdevice. Would you let us know...
Hi
I struggle to understand mechanisms of switching particular subsystem of nrf51822 off and on again in order to consume as little as possible current when MCU is put...
Hi
I have an ADC that just recive, but i will need to make an buffer that makes tx values and just send them to a output pin.
So I wonder how i should code this and if...
I have made custom compiling environment using gcc. I precompile some parts of my software and send to team members .o files what they use in their project so that they don...
Hi, I am using an nRF51822 EK board to develop a custom application and I was wondering about the usage of the SoftDevice. Under what conditions should I use the soft device...
I have recently updated my DFU code to use the source files in SDK 6.1 to be able to OTA upgrade the SoftDevice and Bootloader. I've been able to get the Application to reliably...
Hi,
I am a newbie and would like to build a solution that combines nrf51822 with Arduino. Is this possible.
I find that there are many nrf5001 + Arduino solutions, but...
Hi,
I try to use APP_ERROR_HANDLER(err_code) with a custom error code ( for example 25) in a custom function. Error code reported is correct, but error line and filename...
hello,
Have any example about how to use "CHANNEL_IN_WRONG_STATE" ?
I don't know how to use it. and also don't know when softdevice return this even.
///< Command...
I am having an issue with pin changes triggering interrupts using app_gpiote. I've set up app_gpiote to watch pin 30 and trigger an interrupt on low-to-high or high-to-low...
