hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
In the nRF52 datasheets there is a statement:
"The 64 MHz crystal oscillator (HFXO) is controlled by a 32 MHz external crystal"
Is the crystal somehow oscillating at 2nd...
I am trying to compile the blinky example in the SDK 14.
I am getting this error:
makefile:111: ../../../../../../components/toolchain/gcc/Makefile.common: No such file...
I need an application that always advertise the beacon information, such as RSSI and Major and Minor value. At the same time I would like to transmit HID keyboard code. Is...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
Hello.
This is my code to "wait until micro sd card is pluged".
while(1)
{
disk_state =disk_initialize(0);
if(disk_state==RES_OK)
{
NRF_LOG_INFO("Initialize...
Hello community,
I have a central device which I implemeted, it is running with SD 132 v 4 ("NRF_SD_BLE_API_VERSION=4")
) the chip is a NRF52832, I have some movement...
I have no idea how i can install this and use it.
I would like if any one can explain in detail.
Can you get picture how I can do it?
I am using ble_app_hrs_nfc_pairing...
Hi,
As of now i am using nRF52840 and SDK 14.0.0 and i can find only BLE examples and i wanted to work on bluetooth 5 where can i find examples?.
And i want IR generator...
Hi ,
I am not sure if it is the right place. I was looking for WiFi: 802.11 b/g/n 2.4 GHz support in Arduino UNO and stumble into Arduino primo, which is developed in cooperation...
Hi,
I would like to only connect certain routers in a network using whitelisting. At the moment I'm trying to set a dedicated MAC address to a router and then use this...
Hi,
I am trying to implement the DFU ANT Bootlaoader on my PCA100040 board. I have uploaded the softdevice S212 and the bootloader with nRFgo Studio. I have an ANT dongle...
