Hello and thank you for your help
I am working with the 9151 Rev3 and I attempted to update the IMEI with a valid one provided to us by Nordic
But the following error...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
Hi,
We build a new board based on nRF52833 wlcsp,
I tried to run a simple code with BLE peripheral (ble_app_uart example), and I noticed that the HFCLK is not working...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi
I am running this example from SDK 15.2.0.
I am trying to figure out how the server knows at the end of the session how many bytes of data the Peer received.
Anyone...
The information on the website currently only supports nrf52840.
Can nrf52833 support DFU over USB?
If yes.Which example can be used? Does it use the same DFU USB bootloader...
Hello, I am studying the peripheral/ble_app_uart and peripheral/ble_app/template examples to understand the proper way to build a peripheral with our own set of services and...
Hi,
I have hard time to setup west in my Ubuntu PC. It was installed, but not fully working. So I tried to uninstall and reinstall, and also one time, I may have upgraded...
Hi All,
I have downloaded nrf5_SDK_for_Mesh_v2.2.0_src and trying to build the LIGHT SWITCH example but when i try to compile iam getting lot errors attached the screen...
Hi,
We are currently evaluating nRF52810. I have a couple of queries on DFU:
1. Provided having an application, soft-device, and bootloader in memory, we have to update...
Hello,
I'm using ncs 1.2.0 and trying to compile sample projects like v1.2.0\nrf\samples\sensor\bh1749, also v1.2.0\zephyr\samples\sensor\* but all the defines for device...
Hello,
I'm trying to setup interrupt routines in SPIS1 peripheral.
I have a void IRQ function
But it seems like it never gets called
my init function
some...
Hi,
As I understand Nordic NCS now supports nRF52 development for nrf52832/40/11/10, so based on this I am trying to make a simple application for nRF5232 chip (peripheral_uart...
Hello,
I've been using http/https for some time with Zephyr, and am now venturing into using LTE/NB-IoT on a NRF9160DK board.
Unfortunately, from what I can tell, the...
Hi,
We are working on a Thread network application using nRF52840 DK and would like to interface a WiFi module to this board. We have checked the DevZone and found one similar...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I have added the Buttonless Secure DFU service to my application so that the app can be updated over BLE. It seems working. However, the power management module must...
