Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I am using nRF52 to complement BLE function of MTK7628(they communicate through UART),I've implemented most of the functions.Now I want to add OTA to nRF52, so I use...
I'm trying to combine these 2 examples. I tried adding the uart code:
uint8_t cr;
while (app_uart_get(&cr) != NRF_SUCCESS);
to apps_ble_uart while loop and the whole...
Hi all,
I´m trying to create my first BLE application with segger embedded Studio.
My Hardware is the nRF52833 DK with a sensor connected to dev Board via I2C lines...
Hi, there in inconsistent data about the number of UARTs in the nRF5340 OPS v0.5.1:
- Page ii (nRF5340 features) states "Up to 2x UART (CTS/RTS) with EasyDMA" for the application...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
I Modify my code for 7 buttons from 7 gpios. But my code has a issue at sdk_config.h. The define of GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS is 9. When I built the code and download...
